![]() ![]() If you’re printing a model with two different colors of filament, it will quickly swap between each print head on the fly, navigating to a special corner that physically flips a lever to lower or raise the second print head for printing. There’s also a USB Type-A port at the front to read files off a thumb drive, and a LAN port at the back if you prefer using a wired connection than Wi-Fi.ĭepending on what model you’re printing, the Ultimaker S5 will utilize the correct print head. It’s clear and easy to navigate around, though it can be a bit difficult to read from higher angles. Near the bottom of the Ultimaker S5 is a large, color touchscreen, which is what you’ll use to interact with and set up the printer. Certain users may prefer an aluminum build plate instead, but there’s unfortunately no official way to request one, so you’re stuck with a single glass one for now. We wish that Ultimaker included a second glass panel as well, so that a blank one can be swapped in while the other cools down before a print is removed. Two clips at the front of the bed hold the glass in place, which you can easily slide out again if you want to carefully remove a print from it. The bed itself is heated, and you have a sheet of glass that you slide on top of it. That’s enough room for some fairly sizeable models to print comfortably, and with PVA supports from the second extruder, your prints will remain secure on the print bed. The build volume is quite impressive, sitting in at 330 x 240 x 300 mm (13 x 9.4 x 11.8 inches). There’s a host of other software on offer as well, tailored (and priced) according to your business needs. The price also includes their enterprise software Ultimaker Essentials, which allows for printer management, plugin support, firmware firewalls, and more. The Ultimaker S5 is available now, and is priced at $5,995 (around £4,360 AU$8,080). ![]() Ultimaker Digital Factory – printer management software Ultimaker Cura – print preparation software Printable formats: G, GCODE, GCODE.gz, UFP Ultimaker Cura: STL, OBJ, X3D, 3MF, BMP, GIF, JPG, PNG Print platform: Heated glass build plate (20 - 140 ☌)Ĭontrol interface (display): 4.7-inch (11.9 cm) color touchscreenĬonnectivity: USB port, LAN or WiFi with local or remote access via Ultimaker Cura and Ultimaker Digital Factoryĭimensions and weight (incl Bowden tubes and spool holder): 495 x 585 x 780 mm (19.5 x 23 x 30.7 in), 20.6 kg (45.4 lbs) Print head: Dual extrusion print head with a unique auto-nozzle lifting system and swappable print coresĮxtruder (feeder): Geared feeder with an abrasion-resistant knurled wheel, Bowden extruder setup It will be live and you can ask any questions to our CTO, Miguel Calvo.Print technology: Fused filament fabrication (FFF) We’re hosting a free tech demo on February 7. Reliable bed tilt compensation (no more thumbscrews) 2.4 and 5 GHz Wi-Fi A 1080p camera (mounted higher for a better view) Compatibility with 280+ Marketplace materials Compatibility with S5 project files (no reslicing needed) And a whole lot more The UltiMaker S7 also includes quality of life improvements: We also reversed the front fan direction (fewer plastic hairs, less maintenance), made the print core door magnets stronger, and add a sensor that helps avoid flooding. This effectively makes it much harder to not achieve a perfect first layer, improving overall print success. The re-engineered print head has an inductive sensor which reduces noise when probing the build plate. ![]() Along with that, 4 pins and 25 magnets make it easy to replace the flex plate perfectly – even with one hand. But we also don’t recommend using or adhesion structures for UltiMaker materials (except PC, ’s PC). Not only do you not need tools to pop a printed part off. A PEI-coated flexible steel build plate makes a big difference to productivity. The build stack has also been completely redesigned. To further enclose the build chamber the S7 only has one magnetically latched door. This filters the exhaust air of every print and also improves build temperature stability. It now includes an integrated Air Manager. The UltiMaker S7 is built on the success of the UltiMaker S5 and its design decisions were heavily based on feedback from customers. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |